NAZE32 Acro Pro SP Racing F3 Flight Controller Board For DIY 250 RC

Model: 684380

Specification:
Name: NAZE32 Acro Pro SP Racing F3 Flight Controller Upgrade For 250 RC DIY
Model: 684380
Material: Metal
Size: 35mm x 35mm
Thickness: 8mm
Product Description: Racing F3 Flight Controller (SPRacingF3) was designed to give awesome flight performancebased on tried and tested sensors whilst also providing unparalleled I/O capabilities in a small and extremely
lightweight form-factor using a -generation CPU.
The SPRacingF3 gives you all the features you need for the heart of your , whether youre into FPV racing,
acrobatic flying or photography its perfect.

Features:
1. No compromise I/O. Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED
Strip + Monitoring + Sonar + 8 motors - all at the same time!
2. On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without
guesswork ( Deluxe).
3. -generation F3 processor with hardware floating point unit for efficient flight calculations and faster
ARM-Cortex M4 core.
4. Stackable design - perfect for integrating with OSDs and distribution boards.
5. 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via side
mounted connectors.
6. Full for OneShot ESCs for easy PID tuning and a sharper response.
7. Supports SBus, SumH, SumD, 11024/2048, XBus, PPM, PWM receivers. No external inverters required
(built-in).
8. Dedicated output for programmable LEDs - great for orientation, racing and night flying.
9. Dedicated I2C port for connection of OLED display without needing flight .
10. monitoring ports for voltage and current.
11. Sonar for precision low-altitude hold.
12. Buzzer port for audible warnings and notifications.
13. Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.
14. Symmetrical design for a super tidy wiring.
15. Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.
16. Barometer mounted on the bottom of the board for easy wind isolation.
17. Loop times up to ~2x as fast as previous-generation STM32F1 based boards.
18. Configuration of the flight controller via a cross-platform GUI (Windows/OSX/Linux).
19. Supports a variety of , tricopters, , hexacopters, octocopters, planes and more.
20. Available in Acro and Deluxe versions.
Variations
Acro: Standard model for racing/acro flying.
Deluxe: Additional sensors for altitude and direction.
Software
The SPRacingF3 runs the open-source Cleanflight flight control (FC) software which has an ever-growing community
of friendly developers and users. open-source means that you too can contribute to the system.
Cleanflight comes with a detailed manual that is reviewed and maintained by the Cleanflight developers and
community. No more out-of-date wiki pages and information.

Attention:
Ensure you reference the manual that is appropriate to your version.
History
The hardware was designed by the lead developer of Cleanflight, Dominic Clifton, to be more capable than the
STM32F1-based boards after hearing feedback from the Cleanflight users, contributors and top-pilots.

Failure to adhere to these warnings will void your warranty and destroy your flight
controller.
1. Observe polarity at ALL TIMES. Check and DOUBLE CHECK before applying .
2. OFF before unplugging, plugging in or making any connections.
3. Connect one SOURCE of to the VCC pins / Do not connect more than
one source of to two or more of the VCC pins. e.g. If you are using ESCs
with BECs then remove the center RED wire from all but one ESC connector.
4. Do not connect GND, VCC or 3.3v to each (short circuit).
5. Do not connect GND, VCC or 3.3v to any inputs or outputs unless specifically stated.
6. Do not connect any input or output to any input or output unless specifically
stated.
7. The 3.3v supply is for low-current use . 100mA .
8. Do not allow dirt/dust/etc into the sensor (barometer).
9. Keep magnets away from the flight controller.
WARNINGS
GENERAL ADVICE
Follow the advice below for best performance and long-life of your flight controller:
1. Apply resin/ to reinforce JST-SH connectors - helps if you crash your .
2. Using an enclosure/box for the flight-controller is recommended.
3. Install open-cell foam under the sensor - sandwich some between the FC
and frame.
4. Route motor/ wires as far away from the compass sensor (magnetometer)
as possible.
5. install the BOOT pins if you need them.
6. Using coded pin headers is recommended (not supplied), especially for VBAT
headers.
7. Do everything you can to prevent vibrations reaching the accelerometerro sensor.

Package Included:
1 x Upgrade NAZE32 SP Racing F3 Flight Control for
2 x 8p Wire Rod
2 x 4p Exte






a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a