Zumtobel Victron Quattro Inverter/Charger 48/8000/110-100/100

_x000D_\n_x000D_\n_x000D_\n_x000D_\n_x000D_\nTwo AC inputs with integrated transfer switch_x000D_\n_x000D_\nThe Quattro can be connected to two independent AC sources, for example the public grid and a generator, or two generators. The Quattro will automatically connect to the active source._x000D_\n_x000D_\nTwo AC Outputs_x000D_\n_x000D_\nThe main output has no-break functionality. The Quattro takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Quattro. Loads that should not discharge the battery, like a water heater for example, can be connected to this output._x000D_\n_x000D_\nVirtually unlimited power thanks to parallel operation_x000D_\n_x000D_\nUp to 6 Quattro units can operate in parallel. Six units 48/10000/140, for example, will provide 54kW / 60kVA output power and 840 Amps charging capacity._x000D_\n_x000D_\nThree phase capability_x000D_\n_x000D_\nThree units can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected to provide 162kW / 180kVA inverter power and more than 2500A charging capacity._x000D_\n_x000D_\nPowerControl – Dealing with limited generator, shore side or grid power_x000D_\n_x000D_\nThe Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). A current limit can be set on each AC input. The Quattro will then take account of other AC loads and use whatever is spare for charging, thus preventing the generator or mains supply from being overloaded._x000D_\n_x000D_\nPowerAssist – Boosting shore or generator power_x000D_\n_x000D_\nThis feature takes the principle of PowerControl to a further dimension allowing the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient mains or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery._x000D_\n_x000D_\nSolar energy: AC power available even during a grid failure_x000D_\n_x000D_\nThe Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available._x000D_\n_x000D_\nSystem configuring_x000D_\n

_x000D_\n
• -  In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure.
_x000D_\n
• -  Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software.
_x000D_\n
• -  Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications)._x000D_\n_x000D_\nOn-site Monitoring and control_x000D_\n_x000D_\nSeveral options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power panel, Color Control panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232)._x000D_\n_x000D_\nRemote Monitoring and control_x000D_\n_x000D_\nVictron Ethernet Remote, Victron Global Remote and the Color Control Panel._x000D_\nData can be stored and displayed on our VRM (Victron Remote Management) website, free of charge._x000D_\n_x000D_\nRemote configuring_x000D_\n_x000D_\nWhen connected to the Ethernet, systems with a Color Control panel can be accessed and settings can be changed.
_x000D_\n

_x000D_\n_x000D_\n_x000D_\n_x000D_\n