Visbella Leather And Vinyl Furniture Sofa And Car Seat Repair Kit

Visbella DIY Leather and Vinyl Repair Kit, Do It Yourself Tool Fix Holes, Rips, Upholstery Jacket, Leather Car Seat, Automotive and Household Adhesive.

This repair kit is very handy and easy to help you to repair cracks, cuts, burns and tears on leather and vinyl materials.

Colors and grain papers are designed to match surrounding materials makes repairs blend in with existing A color matching guide helps determine the correct color to match the damaged surface.

With the complete directions that are included in the kit, you can achieve a quality result without the cost or expertise of hiring a professional.

Product Instruction:   

Step 1. prepare and clean the damaged area

Clean the damaged area with a household cleaner. Make sure the area is dry before starting the repair. Carefully trim off frayed, excess threads, of charred material with razor blade or knife. If there is burn damage, remove charred material with razor or knife.

Step 2. Insert backing fabric 

For repairs greater than 1/4 inch, cut the enclosed backing fabric slightly larger than the damaged area. Use the spatula to insert the backing fabric into and under the damaged to provide support for the repair.

Step 3.Choose grain paper

On the top center of the grain paper, make an outline of the damaged area. This will allow you to accurately position the heat transfer in step7.

Step 4. Fill the damage

For deep damages, like a vinyl dashboard, use the vinyl adhesive to glue the backing fabric in place and fill in damaged area to level with the surface. Allow the adhesive to fully dry. This will take 2-3 hours at room temperature a hair dryer can be used to speed up this process). The adhesive will shrink slightly when dry, leaving a void which will be filled in with the colored repair compound later.

Step 5.Matching the color

Prepare the color repair compound while the adhesive is drying. Refer to the provided color chart. Choose from the 7 provided colors by using the spatula to mix small amount of color until correct shade is achieved. If you need to lighten the color, add small drops of white paint and if you need to darken, add small drops of black paint. Check the color accuracy by rubbing a small amount of the color onto the undamaged vinyl; then, remove the compound with a rag.

Step 6. Applying the color repair compound 

Once vinyl adhesive is dry, use the spatula to evenly and neatly apply the repair compound onto the damaged area. Wipe any excess compound from around the hole or damage. Do not overfill the damage area. It is highly recommended to use fewer compounds rather than more. It is easier to add more lately if necessary. Next, tape the grain paper over the uncured color compound making sure the outline is directly over the damaged area. Do not move it. If repair is on a vertical surface, tape the grain paper down.

Step 7. The cure

This is the most important step in the repair process. 

Note: Heating element required. Plug in a hot iron and allow it to warm up for four minutes on a high setting. Place the metal tip of the heat transfer tool directly onto the iron for 2-3 minutes to heat the tool. Then immediately place the metal tip onto grain paper. Rotate the heat tool over the marked circle in a rapid circular motion for 1 minute. For a proper cure, heat must be applied over grain paper. If repair is large, reheat the tool and repeat the procedure as many times as needed until the repair paint is fry. Allow 1-2 minutes for the grain paper to cool. Once cooled, slowly peel off the grain paper and examine the repair. If damaged area is tacky, repeat this step. If there are any pinholes or spots that were not filled in properly, apply small additional amounts of repair compound onto those areas and repeat this step.

Note: Without heat transfer tool step

After step 6, leave the grain paper to dry for 24 hours. Using a hair dryer can speed up this process. Then, tear off the grain paper and the repair is finished.

FREQUENTLY ASK QUESTIONS

1.   Will the repair be strong and able to handle normal wear and tear?

Yes, the backing fabric piece included in the kit ensures a strong and permanent fix.

2.   Can the kit match color leather or fabric?

Yes, a detailed instruction guide is included in the kit that helps you mix the available paint colors to match color of leather or fabric.

3.   What is the largest tear or cut that I can repair with this kit?

The backing fabric piece is 3 inches by 3 inches and will accommodate any tear or cut up to that size

4.   Do I necessarily have to use a clothing iron as my heat source?

No, most typical heat sources will suffice such as a hair dryer.

5.   What if none of the grain papers match the texture of my leather or fabric?

Choose the grain that is the closest match. Once the paint as been applied, the difference between the textures will not be noticeable to the naked eye.