Raspberry Pi 4 Model B Lithium Battery Expansion Board SW6106 5V Output Two-way Fast Charge Mobile For Pi 4B/3B+/Zero

Raspberry Pi 4 Model B Lithium Battery Expansion Board SW6106 5V Output Two-way Fast Charge Mobile for Raspberry Pi 4B/3B+/Zero

Introduction :

The Li-ion Battery HAT integrates SW6106 management , allows providing 5V regulated power supply to your Pi from a 14500 battery, makes the Pi becomes a portable device. It will charge the battery as well, supports a bi-directional quick charge. This module can be used as a universal mini , also works with other 5V devices.

Specifications :

Output voltage: 5V Applicable battery: 3.7V 14500 lithium battery (4.2V when fully charged) - not include in packing Dimension: 65mm × 30mm Mounting hole size: 3.0mm Weight : 21g approx

Features :

Onboard SW6106 , supports a bi-directional quick charge, supports multi quick charge protocols like PD/QC/FCP/PE/SFCP Lithium battery protection circuitry, provides reverse protection, overcharge/discharge protection, overcurrent protection, and short circuit protection Onboard indicators: quick charge, warning, and power capacity

Structure and interface :

1.Raspberry Pi GPIO interface : Easy acce to Raspberry Pi 2. SW6106 power management : USB Type-C interface 3. Battery charge / power output : USB Type-A interface 4. Power output interface : Micro USB interface 5. Battery charging interface 6. Raspberry Pi Power Switch 7. Battery Reverse Warning Light : Lights up when the battery is reversed 8. Battery indicator : Five lights show battery level and charging status 9. Fast charge indicator : Lights up when fast charging is working 10. 14500 battery holder

Dimension :

Packing list :

1 x Li-ion Battery HAT 1 x Screws and Nuts Sets ( not include Raspberry Pi and Battery)

How to USE :

Please refer to the link : https://www.waveshare.com/wiki/Li-ion_Battery_HAT?spm=a2g0o.detail.1000023.1.17ad6234aa9VV

LED indicator in discharge state :

LED indicator in charging state :

Read it before use :

1. The battery needs to be plued into the module, the switch is turned ON, it is charged for about 1 minute and then disconnected, the module will output normally, otherwise there is no output; 2. If the battery is removed, you need to perform the operation again. 3. This module cannot be used as a UPS (Uninterruptible Power Supply). The battery voltage is too low and the Raspberry Pi system will be shut down. 4. You can use the micro USB to directly power the Raspberry Pi's power USB port. 5. Because the height of the module itself is already high, other modules cannot be stacked on the module 6. Do not over-discharge the lithium battery. Due to the characteristics of the lithium battery, over-discharge will permanently damage the battery

Instructions :

1 Insert the module into the Raspberry Pi GPIO interface to power the Raspberry Pi. The switch on the module can control the power supply of the Raspberry Pi. 2 The module's GPIO plued into the Raspberry Pi is actually powered by the USB Type-A interface. If the module is not plued into the Raspberry Pi GPIO, you can use a USB cable to power the Raspberry Pi from the USB Type-A interface. 3 Warning LED is the battery warning light. At this time, you need to unplug the battery and turn it in one direction before connecting it to the module. Do not connect the charging cable when replacing the battery. There is no power output ar replacing the battery. You need to charge the battery to get the power output. 4. There are 5 power indicator LEDs on the module, which can display the battery power status. 5. Quick Charge LED is a fast charge status indicator. Fast charging is only supported when charging with a charger that supports fast charging. Charging with a normal 5V charger will not work and then fast charging. 6. The battery used for the module is a rechargeable 14500 battery, with a nominal voltage of 3.7V, a full charge of 4.2V, and a discharge voltage of 3V. Note: The module cannot be connected with ordinary non-rechargeable No. 7 battery. 7. The discharge time is directly related to the battery capacity. Use an 800mAh battery to power the Raspberry Pi 3B + for about 50 minutes (the power consumption of the Raspberry Pi 3B + will be higher than that of the Raspberry Pi 3B). 2 ~ 3 hours. (Raspberry Pi under zero load) 8. In theory, the module can be connected to a battery with a larger capacity by welding. Non-profeionals do not recommend unauthorized welding.

About shipping
Shipping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days ar buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.