LCR TC1 1.8 Inch TFT LCD Display Multimeter

LCR TC1 1.8 Inch TFT LCD Display Multimeter Transistor Tester Diode Triode Capacitor Resistor Test Meter

• I am an international seller

Our shop sells the most popular 3C consumer electronics products,such as mobile phone accessories,computer accessories,game peripherals,smart wearables,and follow the most popular fashion trends. If you like our products,please follow us,become our follower and fan.We will provide you with the most popular products to satisfy your fashion shopping experience.Is Smart Device : noOperating Mode : HandheldOperating Temperature : 0 - 40 ℃Measuring Capacitance Range : 25pF-100mFMeasuring Resistance Range : 0.01-50 MohmCertification : CEDIY Supplies : ELECTRICALModel Number : LCR-TC1Measuring Inductance Range : 0.01 mH-20H : Mainland ChinaDimensions : 70*90 * 28MMDC Current : ESRAC Current : MOSFETAC Voltage : multimeterDC Voltage : 3.7VDisplay Type : Digital displayTransistor tester: Automatic detection of NPN and PNP bipolartransistors.N-channel and P-chmnnelMOSFETs,JFETs diodes(including double Diodes)N.and P-IGBTS, resisiors, Inductors, , thyristors,triacand battery (0 .1-4.50V)Automatie detection of zener diode (0.01-20v)Self test with automatic calibration IR deer: Support Hitachi lR ing-lR waveform display Other： Measurement results using TFT graphic display(160x128)Auto Power Off(Timeout Settable)Built-in rechargeable Li-ion BatteryLi-ion Battery voltage detection - 160x128 TFT display Warning: Built-in Li-ion Battery, it is strictly prohibited the testerimmersed in water, or near a heat source!Warning: For your personal safety, please strictly comply withthe use of Li-ion Battery specifications and precautions! Power on： In the power off state, short press themultifunction key, the tester is turnedon and automatically measured. Detect transistor: ln the power off state or the test is completed, put the test element into the transistor test area oftest seat, and press the locking handle, short press the multifunction key, the tester automaticallymeasure, graphical display of measurement results when testing is complete.Warning: Always be sure to DISCHARGE before connectingthem to the tester! The tester may be damaged before you have switched it on! Warning: Always be sure to DISCHARGE before connectingthem to the tester! The tester may be damaged before you have switched it on!Warning: We do not recommend using the tester to measure thebattery! The battery voltage must be less than 4.5V, otherwise the testermay be damaged! Detect Zener Diode: When the device is turned off or the test is completed, put the Zener diode into the Zener diodetest area, press the locking handle, and briefly press the multi-function on.Note: Do not put components in theTransistor test area, otherwise theZener diode cannot be tested! Note: Do not put components in theTransistor test area, otherwise theZener diode cannot be tested! lR deer: After the component test is completed, point the infrared remote control at the "IR" test hole of the tester. press the remote control on, the tester will display the user e and data e after successful deing, and display the corresponding infrared waveform.lf the deing fails or the deing fails, the user e and data e cannot be displayed.Atthis time, if you are in the tester interface, you cannot enter the infrared deing interface. If youare in the infrared deing interface, the last successful deing information will still be displayed. Note:This deer only supportsinfrared ening in Hitachi format.Other formats of infrared eningare not supported Automatic calibration: Short-circuit three test sockets, short press the multi-function on, and the tester willautomatically calibrate.During the calibration process, there is no need to perform other operations except to disconnectthe short wire according to the prompts. Shutdown: Automatic shutdown after timeoutWhen the component test is completed or the infrared deing is completed, and the automaticshutdown time is reached, the tester will automatically shut down (overtime 30 seconds) Standby power consumption is 0 UA after shutdown. Battery voltage measurem: Before each component measurement, the built-in lithium battery voltage will be detected anddisplayed. When the battery voltage is less than 3.1V, it will be forced to shut down. Pleasecharge it at this time. Battery charging circuit: The charging interface is a standard Micro USB interface, please use an external 5V powersupply or USB power supply for charging.Note: When the charging indicatoris red, it means charging, and greenmeans charging is complete. FAQ: The charging interface is a standard Micro USB interface, please use an external 5V powersupply or USB power supply for charging.Question:can not power onCause：Lithium battery is lowSolution：Please charge until the light turns greenlnaccurate：Please re-calibratemeasurements：Please re-calibrate Known errors and unsolved problems: 1.The current amplication factor of germanium transistors can be measured too high becauseof the high residual current. In this case the basis emitter voltage will be very low.2.Capacity value in reverse direction for Power Schottk Diodes such as MBR3045PT can not be measured, if only one diode is connected.The reason is a too big residual current of thisdiode. Sometimes the measurement is possible by cooling down the device (with cooling sprayfor example).3.The diode function of a triac gate can not be examined.4.The Source and Drain pins can not be detected correctly with JFET's. The reason is thesymmetrical structure of this semiconductors. You can notice this problem with the elect,that the display shows the same layout with the same pal rameters, if the Source and Drain pinsare swapped.5. The output current of the tester is 6MA/voltage