Contactless Lift Car Door Controll One Foot Activated Auto Professional For Electric Tail Gate Trunk Boot Kick Sensor Open Flaps

Features: Microwave Sensor: One Kick is a microwave sensor mounted on the inside of the rear and sends down microwaves to detect. Tail Box Control: If the inductor detects an effective kick action in the induction area, it will output the corresponding level signal according to the signal intensity to control the opening of the tail box. Convenient: After installing a kick, the owner can easily open the trunk of the car through the kick action, no longer for the hands of large itand feel inconvenient. Fitment: This product just fit the car with electric tail gate lift. Install: There is the enough space in the rearper for installing our sensor. Specification Material: Plastic, electric componebts Color: Black Power supply voltage: DC 5-18 V Starting time: about 2s Operating current: about 5mA Microwave working mode: intermittent Microwave duty cycle: 4.4% Operating temperature :-40-+85 ℃ Emiion frequency: 24.125 0.125 GHz Protection grade: IP68 Extension wire connection method 1, black line (power negative) : lapping; 2. Green line (key line) : keep a good contact with one end of the test pen tower end and the line on the rear door key socket. Pre the rear door on at this time, and the light of the test pen will be off.(diode "test pen) 3. Red line (positive pole of power supply) : connect the car with 12V constant current; 4. line (ACC) : keep good contact with one end of the tower of the test pen and the other end with the measured line. At this time, the car key is preed to ACC, and the light of the test pen will light up Note: After connecting all wires, wait 20 seconds for self-test and then test again Installation steps and precautions (post-installation) : 1. First, wipe the position to be installed on the inside of the rear. It is best to install the sensor in the middle of the rear of the car without leaving soil, dust and water 2. Aimed at the hole mark on the sticker and drilled with a screw of your own, noting that the direction is outside the screw cap; 3. When the screw is drilled into the about 1 cm, stop drilling, and place the holes on the left and right sides of the microwave sensor on the screw drilled. The surface is the induction surface, and the induction surface must be downward to the ground 4. Pre and hold the microwave sensor to continue to screw the screw to fix the microwave sensor. After tightening the screw, the and the inside of the should be completely fitted, and there can be no gap in the middle to prevent the sediment from entering and affect the use effect. 5. If there are mesh, protrusion and other structures on the inside of the on the module can not be completely fitted with the inside of the .The mesh, protrusion and other structures must be polished or filled with gla , otherwise the gap between the water and sediment will greatly affect the performance of the sensor. Package included: 1pc x Sensor Module 1pc x Probe Signal Cable 2pxs x Location Screws 1pc x Location Paper

Note:

1.Due to the difference between different monitors,the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the pictures,,but not the same performance on different bodies as on the model.

2.Compare the detail sizes with yours,please allow 2-4cm differs due to manual measurement for the clothes, thanks All measurement in cm and please note 1cm=0.39inch

1) We accept , , TT.All major credit cards are accepted through secure payment proceor ESCROW.

2 If you can't checkout immediately after auction close, please wait for a few minutes and retry Payments must be completed within .

1) WORLDWIDE SHIPPING. (Except some countries and APO/FPO)

UPS TNT takes 3-7 days ,takes 8-12 days. Post air mail need 2-8 weeks.But all of them are dependent on the country delivered to. 2) SERVICE TRANSIT TIME is provided by the carrier and excludes weekends and holidays. Transit times may vary, particularly during the holiday season.

1) Buyer's early confirmation will be highly appreciated after receiving the items. 2) Since your feedback is very ant to our busine's development, we sincerely invite you to leave positive feedback for us if you are satisfied with our product and service. 3) Please contact us before leaving any negative or neutral feedback. We will work with you to solve any problems.Thank you for your understanding!

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.