1PCS 1S 2S 3S 4S 5S 6S 3A 20A 30A Li-ion Lithium 18650 Charger PCB Protection Board For Drill Motor Lipo Cell Module

1PCS 1S 2S 3S 4S 5S 6S 3A 20A 30A Li-ion Lithium Battery 18650 Charger PCB BMS Protection Board For Drill Motor Lipo Cell Module

• I am an international seller

Our shop sells the most popular 3C consumer electronics products,such as mobile phone accessories,computer accessories,game peripherals,smart wearables,and follow the most popular fashion trends. If you like our products,please follow us,become our follower and fan.We will provide you with the most popular products to satisfy your fashion shopping experience.Package : DIPis_customized : YesModel Number : For Drill Motor Lipo Cell ModuleOperating Temperature : igmopnrqDissipation Power : 1S 2S 3S 4S 5S 6S 3A 20A 30ASupply Voltage : Li-ion Lithium Battery 18650 Charger PCB BMS Protection BoardApplication : for ArduinoCondition : NewType : Voltage RegulatorBrand Name : IBUW : Mainland China1S 3.7V 3AFeatures:1) high-accuracy voltage detection circuit;2) terminal of the charger using high voltage device;3) Built-in three-stage over-current detection circuit (over-current 1, over-current 2, load short circuit);4) MOS transistor can control the battery charge and discharge;Parameter:Over charge voltage: 4.25±0.05VOver charge release voltage:4.23±0.05VOver discharge voltage:2.54±0.1VMaximal continuouscharging current: 2AMaximal continuous Discharging current: 2AOver current protection: 3ASize: L40*W4*T3mm2S 7.4V 3ADescription: Short circuit protection Overcharge protection Over-discharge protection Overcurrent protection Overcharge Detection Voltage: 4.25-4.35V±0.05V Over Discharge Detection Voltage: 2.3-3.0V±0.05V Maximum Working Current: 3A Transient Current: 5A Operating Temperature: -40-50 degree Internal Resistance: Less than 45m Ω B+ B-: The interface of battery core P+ P-: The connector of battery board MB: The connection point between the batteries B+: Battery V+ Positive B-: Battery V- Negative P+: Output / Charging V+ P-: Output / Charging V- Size: Approx. 36x6x1mm/ 1.42" x 0.24" x 0.04" 3S 10A 12V The protection board can not be used for lithium iron phosphate battery, hernia lamp, hand drill battery pack, electric fish battery pack, electric bicycle battery pack, children's car battery, 775 (4A) motor, 1W fish eye LED light, Please pay attention to the combination of the purchase of customers! The Described in the power range for the following products: Massager battery pack, LED light standby power supply, 12V electronic products, solar street lamp battery pack, monitor backup power supply, and other products. Note: 3A current discharge products above, the battery discharge rate to 3C or more. Magnification calculation formula: 1C magnification of the battery, 2000 capacity is equal to 2AH * 1 = 2A upper limit current. 3C magnification battery, 2000 capacity equal to 2AH * 3 = 6A upper working current. In use, the battery will heat is the battery does not apply, this situation can not be -term use, the battery will soon be damaged. Description Explanation: 3 string (for 3 18650 batteries or polymer lithium battery series combination) 10.8V (rated voltage for polymer battery) 11.1V (18650 or 3.7V lithium battery rated voltage) 12.6V (lithium battery is fully charged after the voltage) Discharge 10A (refer to the upper limit discharge current limit) Note 1: strictly according to Figure wiring 0V (B -), 3.7V (B1), 7.4V (B2), 11.1V (B +), do not deliberately short circuit! Note 2: after the need to charge the first line, will have output. Note 3: When connecting three groups of batteries, please ensure that the voltage of each group of batteries, if not the same, please fill each battery separately and then use in series. Discharge test, the voltage drop is fast that group of batteries is poor battery. (2 good battery + a poor battery use effect = 3 poor battery use effect).... The lithium battery protection board properties: Model: HX-3S-01 overcharge voltage range: 4.25-4.35v ± 0.05v Size: 50 * 16 * 1.0mm Over discharge voltage range: 2.3-3.0v ± 0.05v Upper working current: 6-8A Operating temperature: -40 --- +50 ° Upper limit instantaneous current: 9-10A Storage conditions: -40-- +80 ° Quiescent current: less than 30uA Effective life: more than 30,000 hours Internal resistance: less than 100mΩ Short circuit protection: protection, delay self-recovery. Charging voltage: 12.6V-13V The protection board size and device description; The protection board size is 50 * 16 * 1.2mm; components for the Seiko S-8254AA protection chip and AO4407 * 4;3S 12.6V 20A Scope of application: Lithium batteries with nominal voltages of 3.6V and 3.7V (including 18650, 26650, polymer lithium batteries) Product size: 59*20*3.4mm Product weight: 4.3g Charging voltage: 12.6V-13.0V Continuous discharge current (upper limit): 20A (If the heat dissipation environment is not good, please reduce the load current to use) Continuous charging current (upper limit): 10A Standard version: suitable for electric drills with starting current below 40A and power below 65W. Note 1: Successful start of the electric drill requires 3 power batteries of 15C-20C, or 6 power batteries of 10C-15C (ordinary 18650 cannot start the electric drill!! !); if it happens to be the battery is too small or the power of the electric drill is too large If you cannot start, please contact the owner to tell you the solution. Note 2: Wiring 0V, 4.2V, 8.4V, 12.6V strictly according to the diagram, do not intentionally short-circuit. Note 3: For loads with brushed motors, a capacitor (10uF-1000uF) must be connected in parallel to the positive and negative terminals of the motor to prevent the reverse peak voltage generated by the motor from interfering with the protection board or puncturing the MOS tube. Note 4: When connecting 3 sets of batteries in series, please ensure that the voltage of each set of batteries is the same. If they are not the same, please charge each set of batteries separately and use them in series. . . During the discharge test, the battery with the faster voltage drop is a bad battery. Explain for some customers with poor electronic foundation: Never mix good batteries and bad batteries together! The closer the capacity/internal resistance of the 3 sets of batteries, the better! (2 good batteries + 1 poor battery use effect = 3 poor battery usage effects). Explain for some customers with poor electronic foundation: Never mix good batteries and bad batteries together! The closer the capacity/internal resistance of the 3 sets of batteries, the better! (2 good batteries + 1 poor battery use effect = 3 poor battery usage effects). 4S 30A 16.8V 4 string lithium battery protection board, suitable for nominal voltage 14.4V lithium battery pack, 14.8V lithium battery pack, 16.8V lithium battery pack. With automatic activation function, protection conditions automatically restored after the resumption of protection, no need to activate the charger, the use of more convenient.Module : Module name: 4 string lithium battery protection board Modular nature: Polymer lithium battery protection board Overcharge detection voltage: 4.25 ± 0.025V Overcharge release voltage: 4.15 ± 0.05VOver discharge detection voltage: 2.50 ± 0.08VOver discharge release voltage: 3.00 ± 0.1V Overcurrent current: 20-30AOperating current: 15A (natural cooling 10A, plus heat sink 15A, the maximum instantaneous current 30A)Release condition: protection condition is de-automatic recovery without activation (optional charger active) Main functions: overcharge protection, over discharge protection, short circuit protection, overcurrent protection.Operating temperature: -40 ~ +85 degrees (when the ambient temperature is too high, please strengthen the heat) Wiring method: welding output Module size: 50mm * 22mm * 4mm Applications: The protection board can be used as the nominal voltage of 14.4V, 14.8V, 16.8V four-string polymer lithium battery pack, four string 18650 lithium battery pack as overcharge, over discharge, short circuit protection. No need to activate the function In the power application for the instantaneous current is very high, the inverter application can avoid the false trigger protection, the use of more convenient. --------------------------------------------------------------------