10PCS 5V 1A TYPE-C Micro USB 18650 TC4056A Lithium Charging Board Charger TP4056 Module with Protection Dual Functions

10PCS 5V 1A TYPE-C Micro USB 18650 TC4056A Lithium Battery Charging Board Charger TP4056 Module with Protection Dual Functions

• I am an international seller

Our shop sells the most popular 3C consumer electronics products,such as mobile phone accessories,computer accessories,game peripherals,smart wearables,and follow the most popular fashion trends. If you like our products,please follow us,become our follower and fan.We will provide you with the most popular products to satisfy your fashion shopping experience.Hign-concerned Chemical : NonePackage : SMDis_customized : YesModel Number : 18650 Lithium Battery Charging BoardOperating Temperature : -40 -85Dissipation Power : 5V 1ASupply Voltage : 5VApplication : Electric ToyCondition : NewType : Voltage RegulatorBrand Name : diymore : Mainland ChinaFeature 1 : TYPE C USBFeature 2 : 18650 TC4056AFeature 3 : With protectionFeature 4 : MICRO USBFeature 5 : TP4056 mini USBFeature 6 : tp4056 module with protection
10PCS 5V 1A TYPE-C Micro USB 18650 TC4056A Lithium Battery Charging Board Charger Module with Protection Dual Functions TP405618650 type-cDescribe:Input voltage: 4.35-6 v (recommended voltage 5 V)Charge cut-off voltage: 4.2 V +/- 1%Maximum charging current output: 1000 mABattery overcharge protection voltage: 4.28 VBattery Overcharge Boost: 4.00 VBattery discharge protection voltage: 3.0 VBattery discharge termination voltage: 3.2 VBattery: Overcurrent protection current 3ABoard size: about 2.5*1.65 CMLight status: no load light is off, red light is charging, green light is full.18650 MicroDescribe:1. Input voltage: DC 5V;2. Charging cut-off voltage: 4.2V ±1%; 3. Maximum charging current: 1000mA;4. Battery over-discharge protection voltage: 2.5V;5. Battery overcurrent protection current: 3A;6. The input end is equipped with a MICRO USB socket, which can directly use the mobile phone charger as the input power supply to charge the lithium battery;Instructions:1. The MICRO USB socket and the + - pads next to it are the power input terminals, B+ is connected to the positive electrode of the lithium battery, and B- is connected to the negative electrode of the lithium battery. OUT+ and OUT- are connected to the load, which can be connected to the positive and negative poles of the mobile booster board or other loads.2. Connect the battery to B+ B-, insert the charging cable of the mobile phone to the USB socket, the red light is on, it is charging, and the blue light is full.Application: It can be used for charge and discharge protection of 18650, polymer and other lithium batteries with a voltage of 3.6V and 3.7V. Single or multiple batteries can also be used in parallel.Notice:1. When the battery is connected for the first time, there may be no voltage output between OUT+ and OUT-. At this time, connect the module with DC 5V voltage and charge it to activate the protection circuit. The battery is disconnected from B+ B- and then connected again. It also needs to be charged to activate the protection circuit. When using a mobile phone charger as the input power supply, note that the charger and charging cable must be able to support 1A current output, otherwise the module may not be able to charge the battery normally;2. When charging the battery, the load on the OUT terminal should be disconnected, and the positive and negative poles should not be wrongly connected. Please use according to the specifications, otherwise the module will be damaged.18650 miniDescribe:1. Input voltage: DC4.5V-5.5V; IN+ IN- pad wiring or MiniUSB 5V input2. Full charge voltage: DC4.2V3. Charging current: 1A adjustable4. With charging indicator5. Operating temperature: -10℃ +85℃Instructions for use1. After power on, the blue indicator of the module is always on, and the red indicator is slightly bright and flashing2. When the battery is fully charged, the red and blue indicator lights of the module are always onNotice:1. The wiring needs to distinguish the positive and negative poles, and the reverse connection will burn the IC2. The charging needs to be connected with a short and thick wire. If it is too thin or too , the connection resistance will be large, and the charging will be completed.After that, the battery voltage will drop more3. The connection wires must be in good contact, otherwise the battery voltage will drop a lot after charging is completed.4. The output current can be adjusted by itself, and the output can be changed by changing the fixed resistance in the circuit board100mA- 1000mA current5. If the 5V input voltage is too high, such as 5.2V or 5.5V, it will cause insufficient charging current1000mA. This is normal. When the voltage is high, the chip heats up, and the charging current will be automatically reduced.Low chance of chip being burned6. If the charging current is too large, or it is used in a high temperature environment, heat dissipation treatment is required.7. The ammeter for testing current can only be connected in series with the 5V input of the charging board8. The satisfactory effect of the charging current should be 0.37 times the battery capacity. Such as 1000mAH batteryThe charging current is 400mA9. The charging speed is fast, and the charging effect is poor. After charging, the battery voltage drops more.