1 Channel Relay Module Delay Disconnection Triers Delayed Cycle Timing Circuit Switch XY-J02

4225

Wide voltage power supply6 ~ 30V

Interface is clear and simple, powerful, easy to understand, almost meet all the needs

There is a key stop function (STOPkey)With reverse polarity protection, reverse polarity does not burn

Increased sleep mode is enabled,5Minutes without any operation, automatically turn off the monitor any key wakeup

You can set differentOP,CL,LOP, which are independent of each other, were preserved

All setup automatically power-down save

Operating mode

Product Specifications

1:Operating Voltage:6--30V

2: Trier source: high level trier (3.0V-24V) Signal is not coplanar with systematically improved anti- capability (also common ground shorting self)

3: Output capability: to control DC30v5AOr exchange within220v5AWithin equipment

4 with optocoupler isolation, enhanced anti- capability, industriarade circuit board, to set of power forevermemory

pay attention:A paive contact relay output, the output is not charged, controls the action of a break-

Timing range

0.1S (small)~ 999Min (Large) continuously adjustable

How to choose the time range:

In the mode selection interfaceAr setting the parameter valuesdogSTOPkeySelect time range

. XXX decimal point in bits, time range:1second~ 999second

XX.X decimal point in ten, Timing range:0.1second99.9second

X.X.X. decimal point full brightne, Timing range:1minute~ 999minute

For example, you want to setOPYes3.2Seconds, then move the decimal point to the ten, digital display03.2

Parameter Description: OPOn-time,CLOff-time,LOPCycles(1-999Times,"---"Representatives infinite loop)

These are independent of each other, but each of these common mode , e.g.P1.1It is provided on-timeOPYes5Second user wants to switch toP1.2Mode, then enterP1.2When set the ,OPIt will be5second

In the main screen (Show000)dogSETon will be displayedOP(CL,LOP) And the corresponding timeXXX

If only modeOP(Eg modeP1.1,P1.2,P1.3) Time, then preSETKey will display onlyOPAnd the corresponding time

If the pattern hasOP,CL,LOP(Eg modeP3.1,P3.2) That PreSETKey displaysOPAnd the corresponding time,CLAnd the corresponding time,LOPAnd the corresponding number of

Ar setting mode, the main interface by preSETKey can easily view the current mode set, very convenient

How to set

1.First, determine the mode of operation of the relay

2.Depending on the mode of the relay, inMain interface(On power module will flash the current operating mode used (defaultP1.1Mode), then enterMain interface,) "PreSETkey2Ar the second release"enterMode selection interfaceBy short preUP,DOWNon to select the mode to be set (P1.1 ~ P-4)

3.Ar selecting a good mode to be set (for example,P3.2)dogSETkeySet the , the parameter to be set this time flashes (OPOn-time,CLOff-time,LOPCycles("---"Representatives infinite loop)), byUP,DOWNAdjustment parameter values, supports long pre (rapid increase or decrease) with a short pre (increase or decrease1Units); Ar setting the parameter values, bydogSTOPkeyDecimal point position is selected, selection time range (The appropriate time0.1second~ 999minute);dogSETThe parameter key, the current mode is set, the proce supra

4.Setting up the of the selected mode,PreSETkey2secondAr the release, currently set mode will blink at, and then return to the main screen, set the of succe is very simple

Main interface:Relay status display does not work. "000"(No decimal point), activated relays with a decimal point, the very clear

Mode selection interface:PreSETEnter, the setting is completed, preSETTo exit and return to the main interface

STOPKey Function extension

Relay enable mode

1.ON:OPRelays allow the on-time conduction

2.OFF: Relay prohibit conduction is always off

In the main interfacedogSTOPons, to realizeONwithOFFSwitching between the current state of which flashes and then return to the main screen. (This feature is an emergency stop function, a key opening-closing relay)

Sleep Mode:

C-PSleep mode: le than five minutes, without any operation, the LED display automatically shut down, the normal operation of the program

O-dNormal mode: LED is always on display

PreSTOPon2Ar the second release, achieveC-PwithO-dSwitching state, in which the current state of the flash, and then return to the main screen

About shipping
Shipping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days ar buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.