24Hrs Shipping! Yaesu Interface SCU-20 PC Connection Cable FTDI USB To Mini Din 10 Pin For Yaesu FTM-100D/DE/DR FTM-400D/DE/DR

Yaesu Interface SCU-20 PC Connection Cable FTDI USB to Mini Din 10 Pin for Yaesu FTM-100D/DE/DR FTM-400D/DE/DR

Material: PVC outer jacket

Cable: 26AWG*5C, OD4.0 Bare Copper

Cable length:  1.8M optional, other length can be customized

Connector A: USB 2.0 type A male

Connector B: 10-Pin Mini Din Male connector

Chipset: FTDI FT231XS



Application: compatible with Yaesu FTM-100D FTM-100DE FTM-100DR FTM-400D FTM-400DE FTM-400DR








About FTDI FT231

FT231X – Full Speed USB to Full Handshake UART

Key Hardware Features

This USB2.0 Full Speed IC offers a compact bridge to full handshake UART interfaces. The device is a UART, capable of operating up to 3MBaud, with low power consumption (8mA). The FT231X includes the complete FT-X series feature set and enables USB to be added into a system design quickly and easily over a UART interface.




Single chip USB to asynchronous serial data transfer interface.

Entire USB protocol handled on the chip. No USB specific firmware programming required.

Fully integrated 2048 byte EEPROM for storing device descriptors and CBUS I/O configuration.

Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.

Data transfer rates from 300 baud to 3 Mbaud.

512 byte receive buffer and 512 byte transmit buffer utilizing buffer smoothing technology to allow for high data throughput.

FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.

Configurable CBUS I/O pins.

Transmit and receive LED drive signals.

UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity

Synchronous and asynchronous bit bang interface options with RD# and WR# strobes.

Battery Charger Detection. May be used by mobile devices to detect the presence of a charger on the USB port to enable higher current / faster charging of batteries.

Device supplied pre-programmed with unique USB serial number.

Supports bus powered, self powered and high-power bus powered USB configurations.

Integrated +3.3V level converter for USB I/O.

True 3.3V CMOS drive output and TTL input.

(operates down to 1V8 with external pull ups and is also 5V tolerant)

Configurable I/O pin output drive strength.

Integrated power-on-reset circuit.

UART signal inversion option.

Internal 3.3V/1.8V LDO regulators

Low operating current of 8mA (typical) and USB suspend current of 125uA (typical) current.

Low USB bandwidth consumption.

UHCI/OHCI/EHCI host controller compatible.

USB 2.0 Full Speed compatible.

Extended operating temperature range: -40°C to 85°C

Available in compact Pb-free 20 Pin SSOP and QFN packages (both RoHS compliant).




Typical Applications

USB to RS232/RS422/RS485 Converters

Upgrading Legacy Peripherals to USB

Cellular and Cordless Phone USB data transfer cables and interfaces

Interfacing MCU/PLD/FPGA based designs to USB

USB Audio and Low Bandwidth Video data transfer

PDA to USB data transfer

USB Smart Card Readers

USB Instrumentation

USB Industrial Control

USB MP3 Player Interface

USB FLASH Card Reader and Writers

Set Top Box PC – USB interface

USB Digital Camera Interface

USB Hardware Modems

USB Wireless Modems

USB Bar Code Readers

Dedicated Charger Port (DCP) detection enabling battery charging at higher current for faster charge times.