Eco OBD2 Benzine Cars FuelSaver

Nitro OBD2 Full Chip Tuning Box Eco OBD2 Economy Chip Tuning Box OBD Car energy Saver Eco OBD2 for Benzine Cars Fue Saving 15%  

Plug and Drive Eco OBD2 Economy Chip Tuning Box for Benzine 15% FueSave  
 

It works based OBD2 protocols as remaping the Car's computer ECU. After driving 200 km road total, EcoOBD2 adjusts itself to the car, according to the drivers' habits and always keeps remaping the ECU to save energy lower and immission.

 

What does EcoOBD2 make?

 

According to your driving habits,  EcoOBD2 makes new map in the car's computer ECU for the vehicle's lower fel consumption. As you driving much more KM/Mile, EcoOBD2 renews the map and adjusts itself to match your car perfectly for more ful saving.

 

What is EcoOBD2 Chip Tuning Box?

 

EcoOBD2 is a Chip Tuning Box which can be plugged into OBD2 connector of your car to decrease the energy consumption of your car. When it plugged into OBD2 connector, EcoOBD2 receives the information from the car computer ECU. With the received data from ECU, EcoOBD2 adjusts the boost pressure, quantity of energy ,injection timing and pressure to decrease the energy consumption of your car.

EcoOBD2 Chip Tuning Box does not exceed the manufacturer requirements. It works only within the tolerance of the engine.

EcoOBD2 does not damage the engine and the car computer ECU or not cause any negative effects to the car factory setting.

EcoOBD2 does not change any of the settings permanently. To turn back to the car's settings, just unplug EcoOBD2 from OBD2 connector.

 

EcoOBD2 help you save energy consumption:

 

- Up to 15% energy savings

 

EcoOBD2 is very easy to use

 

Plug EcoOBD2 into OBD2 connector of your car. And turn the ignition on for 30 seconds. And Turn the engine on. EcoOBD2 settings are optimal and the best for your car. Even the parameters are different for each vehicle, there might not be a need to make an additional adjustment.

EcoOBD2 will recognize your vehicle and your driving habits after around 200 km/150 miles driving, and then EcoOBD2 adjusts itself to match your car perfectly.

 

EcoOBD2 works on the basis of changing the signal form ECU. As a consequence, it changes the whole injection map.

 

The main difference between EcoOBD2 Chip Tuning Box and Remapping tuning methods is that EcoOBD2 Chip Tuning Box is easily removable, and after unplug you go back to the factory settings. EcoOBD2 is the cheap and safe type of tuning. Remapping is a permanent change to your car. This is the expensive tuning and you cannot remove it. EcoOBD2 is equipped with the engine protection function and 100% safe for your car engine. EcoOBD2 produced on the printed circuit board in SMD technology. EcoOBD2 Chip Tuning Boxes are high quality.

 

EcoOBD2 Installation and Calibration

 

1 - Pull the Car Key out from the ignition.

2 - Find OBD2 connector(*) in your car and Plug in EcoOBD2

3 - Insert the key into the ignition and twist the key to the first stage. (Do not start the car)

4 - Press the reset buttom for about 5 sec. After releasing the buttom, just wait for a while about 30-54 sec. (EcoOBD2 will communicate and establish connection with ECU)

5 - Start up the engine.

6 - EcoOBD2 will recognize your vehicle and your driving habits, after around 200 km/150 miles driving and thus EcoOBD2 will adjust itself to match your car perfectly for more ful saving.

 

Does your car have OBD2 connector?

 

On-Board Diagnostics, or "OBD," is a computer-based system built into all 1996 and later light-duty vehicles and trucks, as required by the Clean Air Act Amendments of 1990. OBD systems are designed to monitor the performance of some of an engine's major components including those responsible for controlling emissions.

 

OBD2 necessarily for cars:

 

- Sold after January 1, 1996 in the USA

- Sold after January 1, 2001 in the European Union

- With gasoline engine sold after January 1, 2003