BIQU TMC2130 V2.0 Silent /DIR/STP Motor Driver For MKS GEN V.4/MKS GEN L/SKR Board

₦ 24,000

₦ 47,00049%

In stock

+ shipping from ₦ 4,450 to LEKKI-AJAH (SANGOTEDO)

0 out of 5

(No ratings available)

Variation available

Promotions

Call 07006000000 To Place Your Order Need extra money? Loan up to N500,000 on the JumiaPay Android app. Enjoy cheaper shipping fees when you select a PickUp Station at checkout.

Report incorrect product information

Delivery & Returns

Shipped from abroad

Choose your location

Pickup Station

Delivery Fees ₦ 4,450

Arriving at pickup station between 21 June & 27 June when you order within next 14hrs 59mins

Door Delivery

Delivery Fees ₦ 4,820

Ready for delivery between 21 June & 27 June when you order within next 14hrs 59mins

Return Policy

Free return within 7 days for ALL eligible itemsDetails

Warranty

Seller Information

Buildings Girl

60%Seller Score

58 Followers

Seller Performance

Order Fulfillment Rate: Very Poor

Quality Score: Excellent

Customer Rating: Average

Product details

Introduction
TMC2130 V2.0 is a new module that is optimized and upgraded to solve the problem that older drivers cannot choose to use the working mode.

TMC2130 V2.0 Upgrade point:
1. working mode of TMC2130 2.0 can directly select driver current, driver subdivision and through , which makes these more accurate. Using sequexternal sequencers, it can greatly reduce the workload of the and effectively avoid problems such as running deviation, losting step and fault caused by the overload of the .
2. The newly upgraded driver, its is at the bottom, which can better dissipate heat
3. This module is similar to TMC2100, which will generate a lot of heat energy when it working.

The File for you to reference:
1. mode : here

Package Included:
1 x TMC2130 V2.0Stepper Motor Driver

Working mode description:
1.STEP/DIR mode:
1.1 position welding 0Ω resistor, making the driver work in STEP/DIR mo
1.2 Work mode selection:SDI(CFG1)/SCK(CFG2)

Note:
In order to enhance the compatibility of drivers, long pin row pin is used in production. When the user uses STEP/DIR mode, it is necessary to check whether the CFG1 pin on the motherboard has connection resistance. If so, it is necessary to remove the resistance or cut off the pin.

2. working mode wiring instructions:
Before wiring, it is necessary to select the hardware operation mode of the driver module

2.1 Solder CFG4 and CFG5 in the red area ( CFG4 is connected to GND and CFG5 is connected to VCC); (Welding is correct to enable spreadcycle mode)

2.2 Remove the resistor at the position to put the driver in mode.
The wiring diagram is as follows
The wiring diagram is as follows:
Found the Aux-3 expansion port on the main board , and the corresponding pin was connected:

a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a