Waterproof Wind Turbine Charge Controller For 1000w 24v Ac Wind Turbine Generator

 Waterproof Wind Turbine Charge Controller for 1000W 24V AC Wind Turbine Generator   Waterproof wind turbine charge controller instructions for use1、Features: The controller can control wind turbine automatically charge the battery. In the case of the battery is filled, through the internal circuit automatic control so that wind turbine brake, when the battery voltage dr ops to the voltage recovery, wind turbine resume charging the battery so as to protect wind turbine and battery. The charging pressure limiting current limit control to ensure the best charging results, provide maximum protection while on the wind turbine and battery. The automatic brake and manual brake complement each other, to meet the different needs of customers. The unique reverse polarity protection circuit. Battery reverse due to improper operation will not need to replace the fuse, the positive and negative polarity reconnected correctly (This feature has won the praise of customers), the entire system run more reliably.The indicating circuit status light-emitting diodes, simple, intuitive and clear.The modular design with independent intellectual property rights, the performance of the entire system to get the maximum protection. Rectifier and brake circuit part of the controller, using the integrated module design, both from the heat, or reliability, further than the traditional design. The comprehensive waterproof protection. Not waterproof controller in 2012, controller board will rust if you use high humidity, or seepage easy envment, the controller is more susceptible to corrosion corrupted, increase the after-sales service of Contractors the workload, and even easier to lose customers. This subsection, the controller uses a fully sealed completely waterproof design, no longer have to worry about the envment, air humidity, salinity, ground water and do not have to worry about the controller water after a short circuit burned, protection grade IP67 above, even if placed in the water is also a long-term normal use, substantially increase the stability and reliability. The controller selection of electronic components and industrial-grade s, key accessories using ary grade product, has a high stability performance of the entire controller. The company has ISO9001 quality management system, products strictly in a variety of aspects of production, testing, quality has been the greatest degree of protection products can guarantee stable at -35 ℃ ~ 70 ℃ high and low temperature envment for long periods.  2、Note:⑴. Confirm consistent wind generator output voltage and rated voltage of the battery.⑵. Following order wiring connected to the battery's positive and negative, were followed by the three-phase voltage output fan.⑶. Carefully follow the instructions require batteries and wind turbines connected to the controller, reverse polarity, or take the wrong position will cause the system is not working properly, or even cause damage to the system components.⑷. Although the controller has taken protective measures for a variety of unexpected situations that may occur, but is still strongly recommended that strict adherence to rules, to prevent causing tremendous damage to the battery and controller.3、Connection mode:Ⅰ. Be respectively connected to the battery "and" - "to the controller of the battery positive and negative terminals.Ⅱ. The three-phase output voltage of the wind turbines are connected to the three-phase voltage input terminals of the controller fan. AndⅢ. When the need to manually brake red thread short battery positive then, to complete the manual brake function, cancel this function, simply disconnecting the thin red line.4、Indicator status:The controller green power (BATTERY) indicator light indicates normal battery access.The controller the green fan access (WIND) indicator flashes, indicating that access to wind turbines, flashing the speed of the fan speed level.The controller red (BRAKE) light is on, the battery is full, wind turbine automatic brake, or due to the over-current protection automatically brake, or is in a state of the manual brake.TypeFW-10-24Battery Rate Voltage24VWind turbine Rated Power1000WBrake start voltage（Default value）30VBrake recovery voltage（Default value）27VDisplayLED(Light emitting diode Display)Operating Temperature Range-35℃-75℃Controller Shell Size150mm*132*48mmQuiescent Current≤20mAProtection classIP67
About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.